DMV Practice LabChange state
INIndiana
DMV Practice LabAll tests

Indiana inspection and skills preparation: test 2

Selected knowledge practice, not a complete licensing course or practical training.

Indiana Inspection and skills preparation Test 2

Practice mode
Question 1 of 16
  1. 1. During the low-speed service-brake check, the truck stops but pulls sharply left. What does that indicate?
  2. 2. Your test vehicle's air safety devices differ from those on the truck you first trained in. What should guide your demonstration?
  3. 3. What must you identify while demonstrating the air-gauge and governor cutoff check?
  4. 4. With the engine stopped, what electrical condition is needed for the low-air warning demonstration?
  5. 5. In the applied air-leakage test described in Section 11, when do you begin the one-minute observation?
  6. 6. One hydraulic-brake test vehicle requires the engine running; another has different power-assist instructions. Which approach is appropriate?
  7. 7. A bus entrance closes securely, but a step tread is loose. Is the entrance inspection satisfactory?
  8. 8. What travel condition should you demonstrate for an equipped passenger lift?
  9. 9. For the modernized bus inspection, how should you address emergency exits?
  10. 10. An equipped school's crossing safety arm is mounted firmly. What operating check is also required?
  11. 11. Why inspect the seals on the school bus's first-aid and body-fluid cleanup kits?
  12. 12. Rust trails or shiny areas appear around wheel fasteners. What are you looking for?
  13. 13. For a tire without an applicable automatic checking system, what demonstrates an actual inflation check?
  14. 14. The steering linkage is not visibly bent. What else belongs in its inspection?
  15. 15. Why inspect spring hangers and mounting hardware as well as the springs?
  16. 16. A brake hose is present but rubbed deeply at a nearby bracket. What should the inspection address?
Review all 16 questions with answers

  1. During the low-speed service-brake check, the truck stops but pulls sharply left. What does that indicate?

    Correct answer: A possible brake problem that needs attention.

    The check assesses both stopping action and whether the vehicle pulls to either side. A pull or poor stopping performance can indicate a braking problem and should not be treated as a pass.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.1.1, Service Brake Check, physical PDF page 138. September 9, 2022 section. Reviewed September 14, 2026. ↗

  2. Your test vehicle's air safety devices differ from those on the truck you first trained in. What should guide your demonstration?

    Correct answer: The test vehicle's manufacturer-specified procedures and equipment.

    Air safety devices vary. Section 11 requires knowing and explaining the specifications for the vehicle being tested; a generic script is not a substitute for understanding its actual system.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.1.2, Air Brake Check, physical PDF page 139. September 9, 2022 section. Reviewed September 14, 2026. ↗

  3. What must you identify while demonstrating the air-gauge and governor cutoff check?

    Correct answer: The cutoff pressure reached by the actual test vehicle.

    Demonstrate that the air gauge works and pressure builds to governor cutoff, then identify that vehicle's cutoff pressure. The end of the gauge scale is not the governor setting.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.1.2, Air Gauge and Governor Cut-off Check, physical PDF page 139. September 9, 2022 section. Reviewed September 14, 2026. ↗

  4. With the engine stopped, what electrical condition is needed for the low-air warning demonstration?

    Correct answer: Keep the key or electrical power in the on position.

    The warning check is performed without restarting the engine, with electrical power on so the warning devices can operate. Know the applicable system's specifications; this question does not prescribe one warning-pressure value for every vehicle.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.1.2, Air Warning Device(s) Test, physical PDF page 139. September 9, 2022 section. Reviewed September 14, 2026. ↗

  5. In the applied air-leakage test described in Section 11, when do you begin the one-minute observation?

    Correct answer: After full foot-brake application and stabilization of the gauge.

    After setting up and securing the vehicle as required, fully apply the foot brake and let the gauge stabilize before measuring the one-minute loss. The initial application drop is not the timed leakage measurement.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.1.2, Air Leakage Rate Test, physical PDF page 139. September 9, 2022 section. Reviewed September 14, 2026. ↗

  6. One hydraulic-brake test vehicle requires the engine running; another has different power-assist instructions. Which approach is appropriate?

    Correct answer: Demonstrate the manufacturer's procedure for the actual system.

    Hydraulic systems and power-assist checks vary. Section 11 calls for the vehicle-specific procedure, including the specified ignition or engine condition, rather than a universal engine-on or engine-off rule.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.1.2, Hydraulic Brake Check, physical PDF page 139. September 9, 2022 section. Reviewed September 14, 2026. ↗

  7. A bus entrance closes securely, but a step tread is loose. Is the entrance inspection satisfactory?

    Correct answer: No; the steps and secure walking surfaces also need inspection.

    The entrance check includes the door, handrails, step lights when equipped, clear steps and secure tread. A working door does not make a loose walking surface acceptable.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.2, Passenger Entry and Lift, physical PDF page 140. September 9, 2022 section. Reviewed September 14, 2026. ↗

  8. What travel condition should you demonstrate for an equipped passenger lift?

    Correct answer: Fully retracted and securely latched, with damage and leaks checked.

    The lift must be fully retracted and latched for travel. The inspection also addresses damage, missing parts, leaks and how correct operation is checked.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.2, Passenger Entry and Lift, physical PDF page 140. September 9, 2022 section. Reviewed September 14, 2026. ↗

  9. For the modernized bus inspection, how should you address emergency exits?

    Correct answer: Demonstrate at least one and explain the others, including warnings.

    Section 11 requires an exit-operation demonstration, identifying how the other exits work, secure closure and working warnings. Electrical warning devices are checked with the key in the on or charged position.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.2, Emergency Exits, physical PDF page 140. September 9, 2022 section. Reviewed September 14, 2026. ↗

  10. An equipped school's crossing safety arm is mounted firmly. What operating check is also required?

    Correct answer: It extends fully and works with the stop-arm system.

    Mounting condition is one part of the check. The safety arm must also function properly with the stop arm and extend fully, with no loose, broken or damaged parts.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.3, Stop Arm(s) and Safety Arm, physical PDF page 141. September 9, 2022 section. Reviewed September 14, 2026. ↗

  11. Why inspect the seals on the school bus's first-aid and body-fluid cleanup kits?

    Correct answer: A broken seal can indicate that contents are missing.

    The handbook calls for both kits to be present and their seals intact. A broken seal can signal missing supplies and needs attention; merely seeing a kit container does not establish its readiness.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.3, First Aid Emergency and Body Fluid Kits, physical PDF page 141. September 9, 2022 section. Reviewed September 14, 2026. ↗

  12. Rust trails or shiny areas appear around wheel fasteners. What are you looking for?

    Correct answer: Possible loose fasteners, missing nuts or damaged stud holes.

    The wheel inspection looks for signs of loose or damaged fastening, including rust trails and shiny surfaces. Explain the warning signs instead of treating the presence of nuts as proof of security.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.5.2, Wheel Fasteners (Lug Nuts), physical PDF page 143. September 9, 2022 section. Reviewed September 14, 2026. ↗

  13. For a tire without an applicable automatic checking system, what demonstrates an actual inflation check?

    Correct answer: Use a tire-pressure gauge rather than judging by a kick.

    A tire gauge measures air pressure; kicking or looking at the tire does not. If special monitoring equipment is fitted, understand its actual function rather than assuming every monitoring system also adjusts pressure.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.5.2, Tires, physical PDF page 142. September 9, 2022 section. Reviewed September 14, 2026. ↗

  14. The steering linkage is not visibly bent. What else belongs in its inspection?

    Correct answer: Secure connections and required nuts, bolts and cotter pins.

    Check the linkage for wear and damage as well as secure mounting and retained connections. An unbent part can still be unsafe if a connection is loose or a required retaining pin is missing.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.5.1, Steering System, physical PDF page 142. September 9, 2022 section. Reviewed September 14, 2026. ↗

  15. Why inspect spring hangers and mounting hardware as well as the springs?

    Correct answer: A sound spring still needs secure, undamaged attachment points.

    Suspension inspection includes the springs and their mounting components. Missing or damaged attachments can be a defect even when the visible spring itself is intact.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.5.2, Springs and Air Bags and Shocks, physical PDF page 143. September 9, 2022 section. Reviewed September 14, 2026. ↗

  16. A brake hose is present but rubbed deeply at a nearby bracket. What should the inspection address?

    Correct answer: Its damage, connections and possible leakage.

    Brake hoses and lines must be checked for damage and leaks, with secure fittings. Simply finding a hose in place does not establish that its condition is safe.

    Source: Indiana CDL Manual (September 2022 modernized edition), Section 11.5.2, Brake Hoses / Lines / Leaks, physical PDF page 143. September 9, 2022 section. Reviewed September 14, 2026. ↗

Report a problem with this question

Question reference: in-cdl-skills-017

Opens a draft in your email app. Review and send it there; nothing is sent automatically.

Draft a correction email

Contact details & help

Study tools & test information

Home / Indiana / CDL practice

Indiana inspection and skills preparation: test 2

Brake checks, passenger access and axle components. 16 questions with immediate explanations. Independent study, not a BMV examination or registered ELDT.

All topics and study tools

Study sources and operating limits

Knowledge preparation for Indiana’s modernized vehicle-inspection and basic-control format, not a hands-on test or training course. BMV adopted the updated requirements on August 12, 2024. Questions cite the Indiana pages we checked; its Sections 11 and 12 correspond to the modernized model, not an older maneuver catalog. Study the correct vehicle-class checklist and actual manufacturer procedures. Inspection comes before basic control, which comes before the road test. Exercise-specific pull-ups and looks are scoring allowances, not everyday safety limits. Follow the examiner and meet the separate licensing and applicable ELDT requirements.

These original DMV Practice Lab scenarios cite their actual sources: Indiana requirements for local rules and the identified handbook or federal source for shared safety topics. We compared the relevant specialist topics with the Indiana manual on September 14, 2026. The short tests and random draws use these 80 practice questions.

Independent knowledge practice, not a BMV examination, registered entry-level driver training (ELDT), medical certification or permission to operate a commercial vehicle. Complete the applicable BMV and training requirements separately. Short tests and random draws are our study formats, not verified official exam lengths or topic weighting.

Read the Indiana manual sectionBMV testing update and approved checklistsInspection, maneuver and road-test study guideFederal rules and coverage notes