Which sequence belongs to the modernized Section 11M basic-control test?
Correct answer: Forward stop, straight backing, forward offset, reverse offset.
Minnesota Section 11M lists Forward Stop, Straight-Line Backing, Forward Offset Tracking and Reverse Offset Backing in that order. Read the instructions for each exercise and ask the examiner to clarify anything you do not understand before starting.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; Modernized maneuver sequence; printed 11M-1; physical PDF page 208; reviewed September 21, 2026. ↗
In a modernized backing exercise, you open the door for a better view while securely stopped but stay in the seat. Does it count as a look?
Correct answer: Yes; opening the door counts even without climbing out.
Opening the door or leaving the seated position counts as a look; walking to the back of a bus does too. Secure the vehicle before a permitted look and do not open the door while moving.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; What counts as a look; printed 11M-1; physical PDF page 208; reviewed September 21, 2026. ↗
How should you leave a truck cab for a permitted look during the modernized backing test?
Correct answer: Secure it, face the truck and maintain three points of contact.
Apply the parking brakes and select neutral before a permitted look. Truck entry and exit use three points of contact facing the vehicle; the handbook separately describes forward-facing bus exit with a firm handrail grip.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; Safe truck versus bus exit; printed 11M-1; physical PDF page 208; reviewed September 21, 2026. ↗
While maneuvering in the modernized basic-control test, the examiner raises a hand to stop you. What should you do?
Correct answer: Stop immediately and follow directions to return within the boundaries.
The handbook requires an immediate stop when the examiner signals. Follow the instructions for returning within the exercise boundaries; do not complete a movement against that signal.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; Examiner stop signal; printed 11M-1; physical PDF page 208; reviewed September 21, 2026. ↗
You stop during a modernized backing exercise, then continue backward without first moving forward. Is the stop itself a pull-up?
Correct answer: No; stopping without changing direction is not a pull-up.
A pull-up is forward movement during a backing exercise to improve position or clear an encroachment. A stop without a direction change is not itself a pull-up.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; Stopping versus a pull-up; printed 11M-1; physical PDF page 208; reviewed September 21, 2026. ↗
Which contact is counted as an encroachment under Section 11M's stated vehicle-part rule?
Correct answer: A low-mounted attachment crossing an exercise boundary.
Minnesota excludes the vehicle mirrors and certain unique parts at door-mirror height or higher from this encroachment rule. A part below that height counts when it touches or crosses a boundary. Follow the examiner's instructions for the actual vehicle.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; Modernized boundary exception; printed 11M-1; physical PDF page 208; reviewed September 21, 2026. ↗
In the modernized forward-stop exercise, what should be positioned in the stop box?
Correct answer: The frontmost part identified by the examiner.
Judge the vehicle's frontmost reference point as explained by the examiner, with the stated high-part exceptions. Section 11M allows one stop for this exercise; front-wheel position alone is not the target.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; Forward-stop reference point; printed 11M-2; physical PDF page 209; reviewed September 21, 2026. ↗
After completing the modernized forward stop, how do you signal that you are ready to be scored?
Correct answer: Set the parking brake, select neutral and sound the horn.
After the controlled stop, Minnesota's archived modernized instructions say to set the parking brake, select neutral and sound the horn. This signals completion so the examiner can score the position; follow the one-stop instruction.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; Signaling exercise completion; printed 11M-2; physical PDF page 209; reviewed September 21, 2026. ↗
How far do you back through the alley in modernized straight-line backing?
Correct answer: Until the front of the vehicle clears the last set of cones.
The end condition uses the front of the vehicle clearing the final cones at the far end of the alley. Watch the whole vehicle's position rather than stopping as soon as the rear gets through.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; Straight-back completion reference; printed 11M-2; physical PDF page 209; reviewed September 21, 2026. ↗
What allowance does Section 11M give for its straight-line backing exercise?
Correct answer: One free pull-up and one permitted exit to look.
The modernized straight-line exercise allows one free pull-up and one safe exit to check position. These are model-specific test allowances, not a general limit on safety checks during everyday backing.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; Straight-back allowances; printed 11M-2; physical PDF page 209; reviewed September 21, 2026. ↗
While steering left through the opening in modernized forward-offset tracking, which tire position matters?
Correct answer: The rightmost rear tire must pass between the cone and the line.
The exercise assesses rear-tire tracking clearance while the vehicle moves forward into the opposite lane. Watch the rightmost rear tire's path through the marked opening, not just the front axle.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; Forward-offset tracking reference; printed 11M-2; physical PDF page 209; reviewed September 21, 2026. ↗
What allowances does Minnesota's archived Section 11M give for forward-offset tracking?
Correct answer: No free back-ups and no permitted exit during the exercise.
Minnesota Section 11M.2.3 scores back-ups, encroachments and rear-tire tracking clearance. It gives no free back-ups and does not permit exiting during the exercise. This archived wording is not a rule that any intermediate stop ends the exercise. Follow the examiner's instructions and finish parallel to the outer boundary, at or before the far-end cones.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; Forward-offset correction limits; printed 11M-2; physical PDF page 209; reviewed September 21, 2026. ↗
Where should you finish modernized forward-offset tracking?
Correct answer: Parallel to the outer boundary, at or before the far-end cones.
The handbook specifies a parallel finish at or before the cones at the far end. Then secure the vehicle, select neutral and sound the horn as instructed.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; Forward-offset finishing position; printed 11M-2; physical PDF page 209; reviewed September 21, 2026. ↗
At the end of modernized reverse-offset backing, what position is required?
Correct answer: Straight in the alley, with the rearmost point in its three-foot box.
Minnesota Section 11M.2.4 requires the vehicle to finish straight within the alley, with its rearmost reference point in the three-foot box. The examiner identifies that point and the permitted high-part exceptions. Do not cross the outer boundary.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; Reverse-offset rear stop box; printed 11M-3; physical PDF page 210; reviewed September 21, 2026. ↗
What allowance is listed for modernized reverse-offset backing?
Correct answer: Two free pull-ups and at most two exits to look.
Section 11M permits two free pull-ups and a maximum of two safe exits to check position for reverse-offset backing. Its allowance differs from straight-line backing, so use the correct exercise instructions.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; Reverse-offset allowances; printed 11M-3; physical PDF page 210; reviewed September 21, 2026. ↗
After the vehicle inspection, what must be passed before proceeding to the road test described after Section 11M?
Correct answer: The basic-control skills test.
The handbook places the basic-control test before the road test. Completing these written practice questions does not pass any hands-on testing stage.
Source: Minnesota Commercial Driver's Manual, archived 2023 (form January 2022); modernized Section 11M supplement, version September 9, 2022; Skills stage progression; printed 11M-3; physical PDF page 210; reviewed September 21, 2026. ↗
