Cargo has been loaded in a way that makes inspection impracticable. What distinction does the federal rule make?
Correct answer: The paragraph (b) inspection exception does not erase general cargo-safety duties.
Paragraph (b)(4) also addresses loads that make cargo inspection impracticable. The exception is limited to that paragraph, not a general authorization for unsafe cargo. Mere convenience is not the stated standard.
Source: 49 CFR 392.9(a) and (b)(4); eCFR title 49 displayed current through September 10, 2026; reviewed September 14, 2026. ↗
Under the federal general cargo rule, how should an article likely to roll be restrained?
Correct answer: Use secured chocks, wedges, a cradle or an equivalent anti-roll method.
The anti-roll method must keep the article from rolling and must not become unintentionally loose or unfastened during transport. Its mere presence is not enough if it can move away.
Source: 49 CFR 393.106(c)(1); eCFR title 49 displayed current through September 10, 2026; reviewed September 14, 2026. ↗
Two articles are secured side by side with transverse tiedowns. What does the general federal rule require about the space between them?
Correct answer: Place them in contact or prevent them from shifting toward each other.
If articles move toward each other, the securement can lose effectiveness. The rule calls for direct contact or another arrangement that prevents that inward movement.
Source: 49 CFR 393.106(c)(2); eCFR title 49 displayed current through September 10, 2026; reviewed September 14, 2026. ↗
A tiedown touches a cargo edge that can cut or abrade it. What is required?
Correct answer: Suitable edge protection that resists abrasion, cutting and crushing.
Use edge protection when contact with the cargo could abrade or cut the tiedown. The protector itself must be able to resist abrasion, cutting and crushing.
Source: 49 CFR 393.104(f)(4); eCFR title 49 displayed current through September 10, 2026; reviewed September 14, 2026. ↗
A strap has a cut that reduces its securement performance. Can it be used merely because several undamaged straps are nearby?
Correct answer: No. A performance-reducing damaged component is not acceptable.
Securement devices must be in proper working order without damage that adversely affects performance. Other equipment does not make a defective component sound.
Source: 49 CFR 393.104(b); eCFR title 49 displayed current through September 10, 2026; reviewed September 14, 2026. ↗
A driver proposes shortening a tiedown by tying a knot in it. What does the federal securement-device rule say?
Correct answer: Tiedowns and securing devices must not contain knots.
The rule prohibits knots in tiedowns and securing devices. Use the appropriate equipment and adjustment method rather than modifying a restraint with a knot.
Source: 49 CFR 393.104(f)(1); eCFR title 49 displayed current through September 10, 2026; reviewed September 14, 2026. ↗
A tiedown's hook can open or release as the truck moves. What must be changed?
Correct answer: Attach and secure it so it cannot unintentionally loosen or release in transit.
A tiedown must remain attached and secured throughout transport. An arrangement that can loosen, open or release while moving does not meet that requirement.
Source: 49 CFR 393.104(f)(3); eCFR title 49 displayed current through September 10, 2026; reviewed September 14, 2026. ↗
A tiedown has a 5,000-lb strap, a 3,300-lb tensioner and 4,400-lb anchor points. Assuming these are the relevant WLL ratings, what limits the assembly's WLL?
Correct answer: 3,300 lb, the lowest component or anchor rating.
The assembly is limited by the lowest component rating, including its tensioner, or the anchor-point rating, whichever is lower. Adding ratings or choosing the strongest part overstates the safe limit.
Source: 49 CFR 393.108(a); official eCFR XML retrieved for September 10, 2026; reviewed September 14, 2026. ↗
For federal WLL determination, how is welded steel chain treated when neither its grade nor its WLL can be identified by markings?
Correct answer: Use the value for grade 30 proof coil chain of its size.
The rule assigns unidentified welded chain the grade 30 proof-coil WLL. This is a rating rule, not a guarantee that a damaged chain is usable or that any chain is adequate for the load.
Source: 49 CFR 393.108(d); official eCFR XML retrieved for September 10, 2026; reviewed September 14, 2026. ↗
An 8,000-lb article is secured with tiedowns under the general federal cargo rule. What minimum aggregate WLL is required, apart from other securement requirements?
Correct answer: 4,000 lb.
The aggregate tiedown WLL must be at least half the article's weight: 8,000 ÷ 2 = 4,000 lb. Calculate each tiedown's contribution correctly and also meet the applicable number, arrangement and performance requirements.
Source: 49 CFR 393.106(d); eCFR title 49 displayed current through September 10, 2026; reviewed September 14, 2026. ↗
A tiedown with a 3,000-lb WLL runs from an anchor on the vehicle directly to an anchor on the cargo. How much does it contribute to aggregate WLL?
Correct answer: 1,500 lb.
A direct vehicle-to-cargo tiedown contributes one-half of its WLL to the aggregate. Here 3,000 ÷ 2 = 1,500 lb. This contribution is different from the tiedown's own rated WLL.
Source: 49 CFR 393.106(d)(1); eCFR title 49 displayed current through September 10, 2026; reviewed September 14, 2026. ↗
A 4,000-lb-WLL tiedown passes around the cargo and attaches to vehicle anchors on the same side. What is its aggregate-WLL contribution?
Correct answer: 2,000 lb.
A tiedown that returns to the same side of the vehicle contributes half its WLL. Do not count it as an opposite-side, over-the-load arrangement merely because it passes around the cargo.
Source: 49 CFR 393.106(d)(2); eCFR title 49 displayed current through September 10, 2026; reviewed September 14, 2026. ↗
