A side-view camera lens is clean, but its display cannot be viewed properly from the driver's seat. Is the check complete?
Correct answer: No; the display must work and be adjusted for viewing.
For an equipped vehicle, check both the camera and the inside display. The image must be operable and viewable from the driving position, just as mirrors need proper adjustment.
Source: Colorado CDL Manual (06/15/23), Section 11M.1.1, Windshield and Traffic Monitoring Devices, physical PDF page 135. Modernized testing model; reviewed September 14, 2026. ↗
The vehicle uses circuit breakers rather than replaceable electrical fuses. How should you address the fuse check?
Correct answer: Explain that arrangement and identify the circuit breakers.
The handbook permits identifying the vehicle's circuit breakers when it is not equipped with electrical fuses. Explain the actual equipment rather than reciting an inapplicable fuse procedure.
Source: Colorado CDL Manual (06/15/23), Section 11M.1.1, Emergency Equipment, physical PDF page 135. Modernized testing model; reviewed September 14, 2026. ↗
An equipped school's crossing safety arm is mounted firmly. What operating check is also required?
Correct answer: It extends fully and works with the stop-arm system.
Mounting condition is one part of the check. The safety arm must also function properly with the stop arm and extend fully, with no loose, broken or damaged parts.
Source: Colorado CDL Manual (06/15/23), Section 11M.3, Stop Arm(s) and Safety Arm, physical PDF page 138. Modernized testing model; reviewed September 14, 2026. ↗
Why inspect the seals on the school bus's first-aid and body-fluid cleanup kits?
Correct answer: A broken seal can indicate that contents are missing.
The handbook calls for both kits to be present and their seals intact. A broken seal can signal missing supplies and needs attention; merely seeing a kit container does not establish its readiness.
Source: Colorado CDL Manual (06/15/23), Section 11M.3, First Aid Emergency and Body Fluid Kits, physical PDF page 138. Modernized testing model; reviewed September 14, 2026. ↗
The steering linkage is not visibly bent. What else belongs in its inspection?
Correct answer: Secure connections and required nuts, bolts and cotter pins.
Check the linkage for wear and damage as well as secure mounting and retained connections. An unbent part can still be unsafe if a connection is loose or a required retaining pin is missing.
Source: Colorado CDL Manual (06/15/23), Section 11M.5.1, Steering System, physical PDF page 139. Modernized testing model; reviewed September 14, 2026. ↗
Your test combination uses a ball-type coupler rather than a fifth wheel. What should you explain?
Correct answer: How that coupler works and the condition of its actual locking parts.
Coupling systems vary. Inspect the system actually installed, including secure mounting, coupler and tongue condition, and the applicable locking and safety devices.
Source: Colorado CDL Manual (06/15/23), Section 11M.6.1, All Other Types of Combinations, physical PDF page 142. Modernized testing model; reviewed September 14, 2026. ↗
At the rear of a combination's trailer, what should you inspect besides lamp operation?
Correct answer: Properly colored, clean and undamaged lenses and reflectors.
The rear check includes the condition and correct color of lenses and reflectors. Working bulbs do not compensate for missing, damaged or obscured reflective surfaces.
Source: Colorado CDL Manual (06/15/23), Section 11M.5.4, Lenses and Reflectors, physical PDF page 141. Modernized testing model; reviewed September 14, 2026. ↗
You find a break in the cargo floor while checking the trailer structure. Why is it relevant?
Correct answer: A damaged floor can permit loss of cargo.
The frame inspection includes cracks, breaks and holes in the cargo area or floor. Securement equipment is not a substitute for sound supporting structure.
Source: Colorado CDL Manual (06/15/23), Section 11M.5.3, Frame(s), physical PDF page 141. Modernized testing model; reviewed September 14, 2026. ↗
After a trailer's tandem assembly has been positioned, what does the inspection need to confirm?
Correct answer: The tandem release lever and locking pins are secure.
The handbook specifically includes the trailer tandem release lever and pins. Their security is a separate check from the axle's chosen position.
Source: Colorado CDL Manual (06/15/23), Section 11M.5.3, Frame(s), physical PDF page 141. Modernized testing model; reviewed September 14, 2026. ↗
During the exterior light check, the brake lamps illuminate but remain on after you release the service brake. Is that satisfactory?
Correct answer: No; they should illuminate on application and turn off on release.
The handbook requires checking both responses: brake lights on with brake application and off with release. A lamp that stays on cannot communicate braking changes correctly.
Source: Colorado CDL Manual (06/15/23), Section 11M.4, Lights Operations Check, physical PDF page 138. Modernized testing model; reviewed September 14, 2026. ↗
You must stop while waiting to make a turn in the road test. How should the front wheels be positioned?
Correct answer: Aimed straight ahead while waiting.
Section 13 specifies straight front wheels while stopped before the turn. Keep the vehicle from rolling and recheck traffic before starting the maneuver.
Source: Colorado CDL Manual (06/15/23), Section 13.1.1, Turns, physical PDF page 130. On-road testing guidance; reviewed September 14, 2026. ↗
After traffic checks and signaling for an expressway exit, where does the handbook describe smooth deceleration?
Correct answer: In the exit lane, continuing within the ramp's lane markings.
Section 13 describes smooth deceleration in the exit lane and continued controlled slowing on the ramp. Stay within its markings and maintain adequate space around the vehicle.
Source: Colorado CDL Manual (06/15/23), Section 13.1.5, Expressway or Rural/Limited Access Highway, physical PDF page 131. On-road testing guidance; reviewed September 14, 2026. ↗
