DMV Practice LabChange state
TNTennessee
DMV Practice LabAll tests

Tennessee CDL inspection and skills study: test 4

Selected knowledge practice, not a complete licensing course or practical training.

Tennessee CDL Inspection and skills study Test 4

Practice mode
Question 1 of 16
  1. 1. Which maneuver is included in the basic-control model printed in Tennessee’s linked handbook?
  2. 2. Under the linked Tennessee model, you securely stop and open the cab door for a better view without climbing out. Does that use a look?
  3. 3. Before a permitted outside look during truck backing practice, which sequence follows the linked Tennessee instructions?
  4. 4. In Tennessee’s linked basic-control model, a high-mounted vehicle part crosses a boundary while the tires stay inside. What does the stated rule count?
  5. 5. You stop while reversing, then continue reversing without moving forward. Is the pause itself a pull-up in the linked Tennessee model?
  6. 6. What outside-look limit does the linked Tennessee model specify for straight-line backing?
  7. 7. Where is the parking space for driver-side parallel parking in the linked Tennessee model?
  8. 8. The examiner assigns conventional parallel parking under the linked Tennessee model. Which space is used?
  9. 9. During the linked Tennessee offset-right backing exercise, the rear is in the target lane but the front has not passed its first cones. Is the described finish reached?
  10. 10. Which destination matches offset back/left in the linked Tennessee model?
  11. 11. The cab fits inside the driver-side parallel space, but part of the trailer remains outside. Does that satisfy the linked Tennessee finish?
  12. 12. After backing without boundary contact, which final position matches the alley-dock exercise in Tennessee’s linked handbook?
  13. 13. Does the linked Tennessee model say that an initial corrective pull-up automatically fails the exercise?
  14. 14. You avoid all cones but finish in a different position from the examiner’s instruction. Is staying inside the boundaries enough?
  15. 15. When leaving a secured bus for a permitted look, what does the linked Tennessee text emphasize?
  16. 16. Before the Tennessee CDL road-skills test, which practical stages must the applicant successfully complete?
Review all 16 questions with answers

  1. Which maneuver is included in the basic-control model printed in Tennessee’s linked handbook?

    Correct answer: Alley docking.

    Alley docking belongs to this published model. Do not substitute the different modernized four-exercise sequence.

    Source: Tennessee agency-linked CDL Manual (May 2022 file), 12.2 Basic-control exercise catalog, physical PDF page 151; July 2017 section / 2005 testing model. Reviewed September 14, 2026. ↗

  2. Under the linked Tennessee model, you securely stop and open the cab door for a better view without climbing out. Does that use a look?

    Correct answer: Yes; opening the door counts.

    A look can be counted before the driver reaches the ground. The published definition also covers leaving the control position or walking to the back of a bus.

    Source: Tennessee agency-linked CDL Manual (May 2022 file), 12.1 Outside vehicle observations, physical PDF page 151; July 2017 section / 2005 testing model. Reviewed September 14, 2026. ↗

  3. Before a permitted outside look during truck backing practice, which sequence follows the linked Tennessee instructions?

    Correct answer: Select neutral, set parking brakes and exit facing the truck with three points of contact.

    Secure the truck before leaving the controls. Safe access matters independently of the scoring allowance.

    Source: Tennessee agency-linked CDL Manual (May 2022 file), 12.1 Securing and exiting a truck, physical PDF page 151; July 2017 section / 2005 testing model. Reviewed September 14, 2026. ↗

  4. In Tennessee’s linked basic-control model, a high-mounted vehicle part crosses a boundary while the tires stay inside. What does the stated rule count?

    Correct answer: An encroachment; the rule covers any vehicle portion.

    This older model does not state the modernized high-part exception. Judge the whole vehicle against the applicable boundaries.

    Source: Tennessee agency-linked CDL Manual (May 2022 file), 12.1 Encroachments, physical PDF page 151; July 2017 section / 2005 testing model. Reviewed September 14, 2026. ↗

  5. You stop while reversing, then continue reversing without moving forward. Is the pause itself a pull-up in the linked Tennessee model?

    Correct answer: No; direction did not change.

    A corrective forward movement and a stationary pause are different actions.

    Source: Tennessee agency-linked CDL Manual (May 2022 file), 12.1 Stops versus pull-ups, physical PDF page 151; July 2017 section / 2005 testing model. Reviewed September 14, 2026. ↗

  6. What outside-look limit does the linked Tennessee model specify for straight-line backing?

    Correct answer: One look.

    Straight-line backing has the smaller allowance. Verify the model used by your examiner before applying any test allowance.

    Source: Tennessee agency-linked CDL Manual (May 2022 file), 12.1 Straight-line observation allowance, physical PDF page 151; July 2017 section / 2005 testing model. Reviewed September 14, 2026. ↗

  7. Where is the parking space for driver-side parallel parking in the linked Tennessee model?

    Correct answer: On the vehicle’s left.

    The driver-side exercise uses the left-hand space; the conventional exercise uses the other side.

    Source: Tennessee agency-linked CDL Manual (May 2022 file), 12.2.4 Driver-side parallel parking, physical PDF page 151; July 2017 section / 2005 testing model. Reviewed September 14, 2026. ↗

  8. The examiner assigns conventional parallel parking under the linked Tennessee model. Which space is used?

    Correct answer: The right-hand space.

    Do not confuse the conventional parking side with driver-side parallel parking.

    Source: Tennessee agency-linked CDL Manual (May 2022 file), 12.2.5 Conventional parallel parking, physical PDF page 152; July 2017 section / 2005 testing model. Reviewed September 14, 2026. ↗

  9. During the linked Tennessee offset-right backing exercise, the rear is in the target lane but the front has not passed its first cones. Is the described finish reached?

    Correct answer: No; the front must pass the first cone set too.

    The exercise describes a whole-vehicle finish in the opposite lane, not merely placing the rear there.

    Source: Tennessee agency-linked CDL Manual (May 2022 file), 12.2.2 Offset back/right, physical PDF page 151; July 2017 section / 2005 testing model. Reviewed September 14, 2026. ↗

  10. Which destination matches offset back/left in the linked Tennessee model?

    Correct answer: A space behind and to the left.

    Identify the target side before beginning the reverse maneuver.

    Source: Tennessee agency-linked CDL Manual (May 2022 file), 12.2.3 Offset back/left, physical PDF page 151; July 2017 section / 2005 testing model. Reviewed September 14, 2026. ↗

  11. The cab fits inside the driver-side parallel space, but part of the trailer remains outside. Does that satisfy the linked Tennessee finish?

    Correct answer: No; the entire vehicle must fit within the space.

    The published parking task includes the entire combination, not just its power unit.

    Source: Tennessee agency-linked CDL Manual (May 2022 file), 12.2.4 Parallel parking completion, physical PDF page 151; July 2017 section / 2005 testing model. Reviewed September 14, 2026. ↗

  12. After backing without boundary contact, which final position matches the alley-dock exercise in Tennessee’s linked handbook?

    Correct answer: Straight inside, with the rear within three feet of the back.

    Both alignment and rear position matter. This is the published alley-dock target, not a modernized reverse-offset stop box.

    Source: Tennessee agency-linked CDL Manual (May 2022 file), 12.2.6 Alley dock finish, physical PDF page 152; July 2017 section / 2005 testing model. Reviewed September 14, 2026. ↗

  13. Does the linked Tennessee model say that an initial corrective pull-up automatically fails the exercise?

    Correct answer: No; initial pull-ups are allowed, while excessive corrections count as errors.

    The text distinguishes initial corrections from excessive ones; it does not supply a universal numerical free-pull-up allowance here.

    Source: Tennessee agency-linked CDL Manual (May 2022 file), 12.1 Corrective pull-ups, physical PDF page 151; July 2017 section / 2005 testing model. Reviewed September 14, 2026. ↗

  14. You avoid all cones but finish in a different position from the examiner’s instruction. Is staying inside the boundaries enough?

    Correct answer: No; the required final position is also assessed.

    Boundary control does not replace reaching the instructed finishing position.

    Source: Tennessee agency-linked CDL Manual (May 2022 file), 12.1 Final position, physical PDF page 151; July 2017 section / 2005 testing model. Reviewed September 14, 2026. ↗

  15. When leaving a secured bus for a permitted look, what does the linked Tennessee text emphasize?

    Correct answer: Keeping a firm hold on the handrail.

    Use safe bus access and the handrail. Do not import a truck-only exit description without checking the vehicle involved.

    Source: Tennessee agency-linked CDL Manual (May 2022 file), 12.1 Safe bus exit, physical PDF page 151; July 2017 section / 2005 testing model. Reviewed September 14, 2026. ↗

  16. Before the Tennessee CDL road-skills test, which practical stages must the applicant successfully complete?

    Correct answer: Pre-trip vehicle inspection and basic vehicle control.

    The current Tennessee licensing page identifies both prerequisites. Written practice does not pass either practical stage.

    Source: Tennessee Commercial Driver License, Apply for a Commercial Driver License: stages before road skills; reviewed September 14, 2026. ↗

Report a problem with this question

Question reference: tn-cdl-skills-local-049

Opens a draft in your email app. Review and send it there; nothing is sent automatically.

Draft a correction email

Contact details & help

Study tools & test information

Home / Tennessee / CDL

Tennessee CDL inspection and skills study: test 4

Tennessee handbook basic-control study. 16 questions with immediate explanations. This is an untimed learning test.

All topics and study tools

Basic-control questions follow the older 2005 model in Tennessee’s linked handbook, not modernized Section 12M. Confirm your examiner’s current format and allowances. Shared inspection and road questions retain their real sources; a written quiz cannot certify practical skills.Read Tennessee’s basic-control section

Twenty-one items use Tennessee’s linked handbook or current licensing page, including the complete basic-control study set. Fifty-nine shared physical-inspection and road scenarios retain their actual Colorado DMV-linked source. Tennessee’s PDF describes the older 2005 testing model; current examiner arrangements remain unconfirmed. Its look and boundary rules are not modernized-test allowances. Equipment checks must follow applicable rules and manufacturer procedures. This is study, not hands-on certification.