In a spring-brake chamber, what normally holds the powerful parking spring back so the brake can release?
Correct answer: Air pressure.
Air holds the parking spring compressed. When that holding pressure is released or lost, the spring can apply the brake; this differs from service brakes that use air to apply.
Source: Ohio CDL Driver Manual, HSY 7605 7/26, Section 5 (July 2017): Spring-brake release; physical PDF page 71 (printed 5-3); reviewed September 14, 2026. ↗
Why can poor brake adjustment weaken both service braking and spring-brake holding on the same wheel?
Correct answer: Both rely on properly adjusted foundation-brake components.
The spring brake and service brake depend on the wheel’s brake mechanism. A spring application does not overcome improper foundation-brake adjustment.
Source: Ohio CDL Driver Manual, HSY 7605 7/26, Section 5 (July 2017): Shared adjustment consequences; physical PDF page 71 (printed 5-3); reviewed September 14, 2026. ↗
On a vehicle with the standard yellow diamond-shaped parking-brake control, how do you apply the parking brakes?
Correct answer: Pull the control out.
The standard yellow diamond control is pulled to apply and pushed to release. Older or special equipment may use a different control, so know the vehicle before operation.
Source: Ohio CDL Driver Manual, HSY 7605 7/26, Section 5 (July 2017): Parking control direction; physical PDF page 71 (printed 5-3); reviewed September 14, 2026. ↗
Why should you avoid a strong service-brake application while spring brakes are applied on a vehicle without anti-compounding protection?
Correct answer: The combined forces can damage brake components.
Service and spring forces can add together at the brake mechanism. Some vehicles have protection, but the driver must not assume every vehicle does.
Source: Ohio CDL Driver Manual, HSY 7605 7/26, Section 5 (July 2017): Brake compounding; physical PDF page 71 (printed 5-3); reviewed September 14, 2026. ↗
A bus is equipped with a modulating valve for spring brakes. What is that control designed to permit?
Correct answer: Gradual control of spring-brake application.
A modulating control can vary spring-brake application rather than providing only an on/off action. Operation and securing the control for parking depend on the vehicle’s instructions.
Source: Ohio CDL Driver Manual, HSY 7605 7/26, Section 5 (July 2017): Modulating parking control; physical PDF page 71 (printed 5-3); reviewed September 14, 2026. ↗
Some buses have a separate reserve that can release the spring brakes in an emergency. What limitation matters?
Correct answer: The reserve permits only a limited number of releases.
An emergency-release reserve is finite and vehicle-specific. Its presence is not permission to continue passenger service with an unsafe braking system.
Source: Ohio CDL Driver Manual, HSY 7605 7/26, Section 5 (July 2017): Emergency release reserve; physical PDF page 71 (printed 5-3); reviewed September 14, 2026. ↗
An older vehicle has a driver-operated front-brake limiting valve marked NORMAL and SLIPPERY. For normal stopping, which setting does the handbook specify?
Correct answer: NORMAL.
The handbook specifies NORMAL to preserve normal stopping power. This question concerns the older manually controlled limiter, not ABS or a modern automatic system.
Source: Ohio CDL Driver Manual, HSY 7605 7/26, Section 5 (July 2017): Older front-brake limiter; physical PDF page 71 (printed 5-3); reviewed September 14, 2026. ↗
What makes a dual air-brake system different from one single air circuit?
Correct answer: It has two air systems with separate reservoirs and lines.
Dual systems have separate air circuits operated through a common brake control. The exact axle arrangement depends on the vehicle.
Source: Ohio CDL Driver Manual, HSY 7605 7/26, Section 5 (July 2017): Dual-system separation; physical PDF page 73 (printed 5-5); reviewed September 14, 2026. ↗
Before moving a vehicle with two service-air circuits, what should you check on the pressure gauges?
Correct answer: That both circuits have reached the required operating pressure.
The handbook says to allow both systems to build adequate pressure. One satisfactory reading does not establish that the other circuit is ready; follow the vehicle’s specified procedure.
Source: Ohio CDL Driver Manual, HSY 7605 7/26, Section 5 (July 2017): Checking both circuits; physical PDF page 73 (printed 5-5); reviewed September 14, 2026. ↗
One circuit in a dual air-brake system loses pressure during a trip. Why is continuing the trip unsafe?
Correct answer: Some braking may be lost and stopping distance can increase.
A surviving circuit provides limited protection during failure, not normal service capability. Stop safely and have the problem corrected.
Source: Ohio CDL Driver Manual, HSY 7605 7/26, Section 5 (July 2017): One circuit loses pressure; physical PDF page 73 (printed 5-5); reviewed September 14, 2026. ↗
What should be inspected when the air compressor is belt-driven?
Correct answer: The belt’s condition and proper tension.
A worn, damaged or improperly tensioned drive belt can affect compressor operation. This check applies when the compressor uses a belt, not a gear drive.
Source: Ohio CDL Driver Manual, HSY 7605 7/26, Section 5 (July 2017): Belt-driven compressor inspection; physical PDF page 73 (printed 5-5); reviewed September 14, 2026. ↗
An automatic slack adjuster repeatedly needs manual readjustment. What is the sound response?
Correct answer: Have a qualified person find and repair the underlying fault.
Repeated manual readjustment can hide a problem in the adjuster, installation or foundation brake. It does not replace diagnosis and proper repair.
Source: Ohio CDL Driver Manual, HSY 7605 7/26, Section 5 (July 2017): Automatic slack-adjuster fault; physical PDF page 74 (printed 5-6); reviewed September 14, 2026. ↗
Is one inch the universal legal maximum applied pushrod stroke for every commercial-vehicle brake chamber?
Correct answer: No; use the limit for the actual actuator type and size.
Federal limits depend on the actuator. The handbook’s approximate manual free-play check must not be confused with a universal applied-stroke limit. Unlisted actuator types have the manufacturer-related limits specified by the rule.
Source: 49 CFR 393.47(e)(1)–(2); actuator-specific principle only, no table value reproduced. Official eCFR XML dated September 10, 2026; reviewed September 14, 2026. ↗
During inspection, you find oil or grease on a brake lining. How should you regard it?
Correct answer: As a brake defect that needs attention before safe operation.
Brake linings rely on controlled friction. Oil or grease contamination is an unsafe condition, not a desirable lubricant for the friction surface.
Source: Ohio CDL Driver Manual, HSY 7605 7/26, Section 5 (July 2017): Contaminated brake lining; physical PDF page 74 (printed 5-6); reviewed September 14, 2026. ↗
An air hose is rubbing against a sharp metal edge. What should you recognize?
Correct answer: The rubbing can damage the hose and cause air loss.
Inspect hoses for cuts, rubbing and damage. A warning device can alert the driver to pressure loss but cannot prevent a damaged hose from leaking.
Source: Ohio CDL Driver Manual, HSY 7605 7/26, Section 5 (July 2017): Damaged air hose; physical PDF page 74 (printed 5-6); reviewed September 14, 2026. ↗
Before releasing parking brakes for the handbook’s stationary applied-air-leak test, what is essential?
Correct answer: Secure the vehicle against rolling, including proper wheel chocks.
Some air-system checks require releasing the parking brakes. Establish proper rollaway protection first and follow the vehicle’s full inspection procedure.
Source: Ohio CDL Driver Manual, HSY 7605 7/26, Section 5 (July 2017): Applied-leak test preparation; physical PDF page 74 (printed 5-6); reviewed September 14, 2026. ↗
