DMV Practice LabAll tests

Ohio random tank vehicles practice

Selected knowledge practice, not a complete licensing course or practical training.

Start a practice test or explore the sample questions below.

Explore sample questions with answers

These public examples are not a selection of your saved mistakes.

Sample practice questions

Practice mode
Question 1 of 12
  1. 1. A CDL-required truck is designed to carry water in one permanently mounted 1,500-gallon tank. Can it be a tank vehicle even though the water is not hazardous?
  2. 2. A CDL-required truck is designed to transport liquid in two attached tanks rated 150 and 850 gallons. Do these capacities meet the federal tank-vehicle capacity thresholds?
  3. 3. A CDL-required truck carries liquid in ten attached tanks, each rated exactly 119 gallons. Do those tanks meet the individual-capacity condition in the federal tank-vehicle definition?
  4. 4. A CMV carries an empty 1,500-gallon storage-container tank that is not designed for transportation and is temporarily attached to a flatbed. How does the federal tank definition treat this specific case?
  5. 5. Why should a driver consult the operator’s manual when inspecting an unfamiliar tank vehicle?
  6. 6. You find liquid leaking from the tank shell before loading is complete. What is the proper response?
  7. 7. Before loading, unloading or moving a tanker, what must you verify about its intake, discharge and cutoff valves?
  8. 8. Where should a tanker driver pay particular attention when checking pipes, hoses and connections for leakage?
  9. 9. What should be checked about tank manhole covers?
  10. 10. Why must tank vents be kept clear and functional?
  11. 11. A tanker is equipped with an emergency shut-off system. What should be established before operating it?
  12. 12. Which fitted equipment requires checking as part of tank-vehicle inspection?
Review all 12 questions with answers
  1. A CDL-required truck is designed to carry water in one permanently mounted 1,500-gallon tank. Can it be a tank vehicle even though the water is not hazardous?

    Correct answer: Yes; the tank definition is not limited to hazardous liquids or gases.

    The definition covers liquid or gaseous material in qualifying tanks. Tank-vehicle endorsement requirements are separate from whether a hazardous-material endorsement is also needed.

    Source: 49 CFR 383.5, definition of Tank vehicle; 383.93(b)(3); official eCFR XML as of September 11, 2026; reviewed September 14, 2026. ↗

  2. A CDL-required truck is designed to transport liquid in two attached tanks rated 150 and 850 gallons. Do these capacities meet the federal tank-vehicle capacity thresholds?

    Correct answer: Yes; each exceeds 119 gallons and together they total 1,000 gallons.

    The definition uses individual rated capacity greater than 119 gallons and aggregate rated capacity at least 1,000 gallons. Permanent and temporary attachment can both qualify.

    Source: 49 CFR 383.5, definition of Tank vehicle; official eCFR XML as of September 11, 2026; reviewed September 14, 2026. ↗

  3. A CDL-required truck carries liquid in ten attached tanks, each rated exactly 119 gallons. Do those tanks meet the individual-capacity condition in the federal tank-vehicle definition?

    Correct answer: No; the individual rated capacity must be more than 119 gallons.

    Although their total exceeds 1,000 gallons, exactly 119 gallons does not satisfy the more-than 119 individual threshold. This answer concerns the tank definition, not exemption from other CDL or cargo rules.

    Source: 49 CFR 383.5, definition of Tank vehicle; official eCFR XML as of September 11, 2026; reviewed September 14, 2026. ↗

  4. A CMV carries an empty 1,500-gallon storage-container tank that is not designed for transportation and is temporarily attached to a flatbed. How does the federal tank definition treat this specific case?

    Correct answer: It excludes that specified empty storage-container movement from tank-vehicle classification.

    The definition has a narrow exception for this empty storage-container situation. It does not apply to every empty transport tank or remove unrelated requirements.

    Source: 49 CFR 383.5, definition of Tank vehicle, final sentence; official eCFR XML as of September 11, 2026; reviewed September 14, 2026. ↗

  5. Why should a driver consult the operator’s manual when inspecting an unfamiliar tank vehicle?

    Correct answer: Tank designs and special equipment vary, so the inspection must fit that vehicle.

    The handbook requires tank-specific checks in addition to normal vehicle inspection. Know the vehicle’s equipment before loading, unloading or driving.

    Source: Ohio Commercial Driver License Manual, HSY 7605 7/26, Section 8 (July 2017); Tank-specific inspection instructions; physical PDF page 95 (printed 8-1); reviewed September 14, 2026. ↗

  6. You find liquid leaking from the tank shell before loading is complete. What is the proper response?

    Correct answer: Stop the unsafe operation and have the leak addressed before carrying the load.

    Do not carry liquid or gas in a leaking tank. Follow the appropriate emergency and repair procedures for the material and do not improvise a containment or repair method.

    Source: Ohio Commercial Driver License Manual, HSY 7605 7/26, Section 8 (July 2017); Leaking tank; physical PDF page 95 (printed 8-1); reviewed September 14, 2026. ↗

  7. Before loading, unloading or moving a tanker, what must you verify about its intake, discharge and cutoff valves?

    Correct answer: They are in the correct positions for the operation being performed.

    Different operations require the proper valve configuration. Verify the actual system’s instructions; driving with open discharge valves is not a safe shortcut.

    Source: Ohio Commercial Driver License Manual, HSY 7605 7/26, Section 8 (July 2017); Valve positions; physical PDF page 95 (printed 8-1); reviewed September 14, 2026. ↗

  8. Where should a tanker driver pay particular attention when checking pipes, hoses and connections for leakage?

    Correct answer: Around joints and connection points.

    Joints and connections are important potential leak points. Inspect the whole system rather than assuming an undamaged tank shell means the plumbing is sound.

    Source: Ohio Commercial Driver License Manual, HSY 7605 7/26, Section 8 (July 2017); Hose-joint inspection; physical PDF page 95 (printed 8-1); reviewed September 14, 2026. ↗

  9. What should be checked about tank manhole covers?

    Correct answer: Their gaskets are present and the covers close correctly.

    Correctly sealed covers help contain the cargo. Designed venting must remain functional; an open cover is not a substitute for a proper vent system.

    Source: Ohio Commercial Driver License Manual, HSY 7605 7/26, Section 8 (July 2017); Manhole sealing; physical PDF page 95 (printed 8-1); reviewed September 14, 2026. ↗

  10. Why must tank vents be kept clear and functional?

    Correct answer: They must perform their designed venting function.

    Inspect vents as part of the tank system and follow the equipment’s instructions. Blocking them or substituting an open cover can create an unsafe condition.

    Source: Ohio Commercial Driver License Manual, HSY 7605 7/26, Section 8 (July 2017); Tank vents; physical PDF page 95 (printed 8-1); reviewed September 14, 2026. ↗

  11. A tanker is equipped with an emergency shut-off system. What should be established before operating it?

    Correct answer: That the system is present, functional and understood by the driver.

    Check fitted emergency equipment and learn how it operates. The necessary equipment and procedure depend on the tank and material; this quiz does not replace operational training.

    Source: Ohio Commercial Driver License Manual, HSY 7605 7/26, Section 8 (July 2017); Emergency shut-off equipment; physical PDF page 95 (printed 8-1); reviewed September 14, 2026. ↗

  12. Which fitted equipment requires checking as part of tank-vehicle inspection?

    Correct answer: Grounding or bonding cables and vapor-recovery equipment, when provided.

    The handbook lists vapor recovery, grounding and bonding, emergency shut-offs and built-in fire extinguishers among equipment to check when fitted.

    Source: Ohio Commercial Driver License Manual, HSY 7605 7/26, Section 8 (July 2017); Special-purpose equipment; physical PDF page 95 (printed 8-1); reviewed September 14, 2026. ↗

Report a problem with this question

Question reference: oh-cdl-tank-001

Opens a draft in your email app. Review and send it there; nothing is sent automatically.

Draft a correction email

Contact details & help

Study tools & test information

Home / Ohio / CDL

Ohio random tank vehicles practice

Answer 20 questions from this specialist topic only. This is our untimed study format, not the verified length, timing or scoring of an official BMV test.

Study notes: tank vehicles

These classification scenarios assume a CDL-required vehicle. Individual rated capacity must exceed 119 gallons and aggregate rated capacity must reach 1,000 gallons; there is a narrow empty storage-container exception. Tank qualification does not by itself authorize hazardous-material transport. Inspection, expansion space and operating procedures depend on the actual tank and product.

Capacity, weight and movement are different checks

  • Two qualifying attached tanks rated 150 and 850 gallons meet the 1,000-gallon combined capacity condition.
  • Ten tanks rated exactly 119 gallons do not meet the individual more-than-119 condition.
  • Available tank volume does not cancel weight limits or the space needed for liquid expansion.

Bulkheads separate compartments. Baffles allow flow through openings and reduce forward-and-back surge; they do not eliminate side-to-side movement. Smooth-bore tanks need particular care during starts and stops. Use the actual equipment's braking instructions, not a blanket stab-braking rule for ABS.

These 24 independent questions reuse the same records across short tests and random draws. They do not replace the official examination, applicable ELDT or hands-on training. The Ohio manual is marked HSY 7605 7/26; these chapters retain July 2017 footers. Each answer includes an explanation.

Read the official Ohio chapter