During the modernized inspection test, is naming a component enough to earn credit?
Correct answer: No; identify it and explain what you are checking
Name, point to and/or touch the item, and explain its relevant safety condition.
Source: Texas DL-7C March 2026, section 11, PDF page 147; modernized test ↗
What writing may you add to the permitted inspection checklist before the test?
Correct answer: No additional notes or markings
The checklist may be checked off during the test; it is not permission to bring prepared answers.
Source: Texas DL-7C March 2026, section 11, PDF page 147; modernized test ↗
A training truck has component labels added by a student rather than its manufacturer. May it be used for the modernized vehicle inspection test?
Correct answer: No
The chapter excludes vehicles with non-manufacturer component markings or labels.
Source: Texas DL-7C March 2026, section 11, PDF page 147; modernized test ↗
The inspection test samples one axle. What should your preparation cover?
Correct answer: The same inspection on every vehicle axle
The test sample does not reduce the driver’s real inspection responsibilities.
Source: Texas DL-7C March 2026, section 11, PDF page 147; modernized test ↗
How should you enter or leave a truck cab during the inspection test?
Correct answer: Face the vehicle and maintain three points of contact
Secure the vehicle before leaving. Bus entry and exit use their separate handrail guidance.
Source: Texas DL-7C March 2026, section 11, PDF page 147; modernized test ↗
Your test vehicle uses circuit breakers instead of electrical fuses. What should you tell the examiner?
Correct answer: Identify the circuit breakers and explain that fuses are not used
Explain the equipment actually fitted to the vehicle.
Source: Texas DL-7C March 2026, section 11.1.1, PDF page 148; modernized test ↗
How do you demonstrate the windshield washer portion of the inspection?
Correct answer: Check fluid and activate the washers
Operating the washers shows whether they work; also inspect and operate the wipers.
Source: Texas DL-7C March 2026, section 11.1.1, PDF page 148; modernized test ↗
During the modernized service-brake demonstration, what starting speed does the handbook specify?
Correct answer: 5 mph
Apply the foot brake and stop completely, checking for poor braking or pulling to either side. Perform the demonstration only in the safe test area as directed.
Source: Texas DL-7C March 2026, section 11.1.1, PDF page 149; modernized test ↗
How many parts must you correctly explain and perform in the modernized air-brake check?
Correct answer: Four
The check covers governor cutout, leakage, low-air warning and emergency brakes. Failure to perform all four correctly is an automatic inspection-test failure.
Source: Texas DL-7C March 2026, section 11.1.2, PDF page 149; modernized test ↗
When does the one-minute applied air-leakage measurement begin in the modernized check?
Correct answer: After the gauge stabilizes following the initial application drop
Hold the foot brake fully applied through the measurement. This is not the separate brakes-released leakage check.
Source: Texas DL-7C March 2026, section 11.1.2, PDF page 149; modernized test ↗
Your vehicle’s air-brake valves are not designed to pop out. How does the chapter say to recognize emergency brake application?
Correct answer: Listen for air discharging and explain the manufacturer-specific procedure
Know the actual vehicle specifications; a generic script is not enough for every system.
Source: Texas DL-7C March 2026, section 11.1.2, PDF page 149; modernized test ↗
An automated light-check sequence is running. Does that eliminate the external light inspection?
Correct answer: No; external operation still has to be checked
Automation activates the lights, but does not establish that the exterior lamps illuminate properly.
Source: Texas DL-7C March 2026, section 11.4, PDF page 151; modernized test ↗
During the tire-pressure inspection, will kicking the tires earn credit as a pressure measurement?
Correct answer: No; mention a tire gauge, or the applicable automatic monitoring system
The handbook specifies a gauge and gives separate guidance for connected ATIS or TPMS equipment.
Source: Texas DL-7C March 2026, section 11.5.2, PDF page 152; modernized test ↗
During a backing exercise, you stop without changing direction. Is that alone a pull-up?
Correct answer: No
A pull-up involves moving forward during a backing exercise to improve position or clear an encroachment.
Source: Texas DL-7C March 2026, section 12.1, PDF page 162; modernized test ↗
You open the cab door while stopped to check your backing position without fully getting out. Does it count as a look?
Correct answer: Yes
Opening the door or leaving the seated position counts. Opening it while moving may cause an unsafe-act failure.
Source: Texas DL-7C March 2026, section 12.1, PDF page 162; modernized test ↗
In modernized straight-line backing, how many free pull-ups are allowed?
Correct answer: One
The exercise also permits one safe exit to check position. Follow the examiner’s instructions.
Source: Texas DL-7C March 2026, section 12.2.2, PDF page 163; modernized test ↗
In modernized reverse offset backing, how many free pull-ups are allowed?
Correct answer: Two
The chapter also allows at most two safe exits to check the vehicle’s position.
Source: Texas DL-7C March 2026, section 12.2.4, PDF page 164; modernized test ↗
In the modernized forward-stop exercise, how many stops may you make to position the vehicle?
Correct answer: One
Judge the frontmost part identified by the examiner and make the controlled stop within the indicated box.
Source: Texas DL-7C March 2026, section 12.2.1, PDF page 163; modernized test ↗
During the moving portion of forward offset tracking, may you stop and reverse to reposition?
Correct answer: No
The exercise assesses continuous forward maneuvering. This restriction never overrides a need to stop for safety or an examiner’s stop signal.
Source: Texas DL-7C March 2026, section 12.2.3, PDF page 164; modernized test ↗
How should you signal that a basic-control exercise is finished?
Correct answer: Set the parking brake, select neutral/park and sound the horn
Finish in the required position and secure the vehicle before signaling completion.
Source: Texas DL-7C March 2026, section 12, PDF page 163; modernized test ↗
